AQUAPRO 2120 Water Based Dye Stain
AQUAPRO 2120 Water Based Dye Stain
Interior use only. Timber floors, architraves, skirting boards, timber quadrant and beading.
- Versatile – Can be applied over all species of timber
- Medium to slow dry, easy to apply – results in a uniform colour
- Apply by brush, wiping, roller or applicator – no need to wipe off
- Can be top coated with AQUAPRO water based, DURAPOL moisture cure, POLYTHANE two pack, NATUROIL oil finishes and FASTASEAL sealers
- Good light stability of the dye stain
- Low odour
- Non-flammable, no requirements for precautions with oily rags and equipment
- Water wash up
Colour : Primary: #5000 Yellow, #7000 Red, #8000 Blue, #9999 Black. Premixed: #6001 Maple, #6004 Oak, #6007 Teak, #6008 Walnut
Thinner : AQUAPRO 1320 Slow or 133 Medium Reducer
Coverage : 10-12m2 per litre – coverage is dependent upon the porosity of the timber
Dry Time : Refer to datasheet
Clean Up : Water or AQUAPRO 1320 or 1330 reducer
Packaging : 1 & 5L
Surface Prepartion:
Preparation: Prepare a test area to check colour and application. Prepare the surface by filling nail holes and imperfections with a water based putty in a colour close to the stain. Allow to dry. Sand floor per AS 4786.2-2005 standard to produce a defect and scratch free surface. Finish sanding with 120-180 screen back paper fitted to a rotary sanding machine. Ensure floor is defect and scratch free before applying the stain. Scratches and imperfections may be highlighted by the stain.
Mixing: Stir thoroughly before use.
Tools: Brush, rag, roller or applicator – wipe on and leave or wipe on wipe off.
Application:
- Reduce and mix enough stain for the entire project before starting. Work from one corner as you would when coating a room. Apply to strip flooring along the direction of the grain. Only cut in a small distance in front of your roller or pad applicator. DO NOT pour or pool stain on the floor. Even application of the stain is essential to ensure a uniform even colour.
- Allow the stain to dry before applying coatings (see recoat time).
- Ensure adequate coating is applied to seal AQUAPRO 2120 Stain to reduce the risk of sanding through the sealer coat. If this happens, it is possible to reapply the stain to these areas to re-colour the exposed timber.
- First Coat / Sealer product options: FASTASEAL 3030 Clear Sealer, FASTASEAL 3540 Clear Sealer, DURAPOL 1045, 5840, 1044, 1050, NATUROIL 3100, 3120 or POLYTHANE 2043 Two Pack.
- Second and Final coat: Any of the above plus, AQUAPRO 8270 Advance 2K or NATUROIL 3115 Low Sheen or DURAPOL Low Sheen coatings.
AQUAPRO 2770 Water Based Pigment Stain
AQUAPRO 2770 Water Based Pigment Stain
Interior use only. Timber floors, architraves, skirting boards, timber quadrant and beading
A water based pigment stain designed to achieve a uniform consistent colour that softens the grain definition providing a colour washed effect. Available in white and pastel colours for a lime wash effect. Apply by brush, wiping or applicator before wiping off.
- Versatile – Can be applied over all species of timber
- Medium to slow dry, easy to apply – results in a uniform colour
- Apply by brush, wiping, roller or applicator – nbefore wiping off
- Can be top coated with AQUAPRO water based, DURAPOL moisture cure, POLYTHANE two pack, NATUROIL oil finishes and FASTASEAL sealers
- Good light stability of the dye stain
- Low odour
- Non-flammable, no requirements for precautions with oily rags and equipment
- Water wash up
Colour : Liming Wash, Puff Haze, Greystone, Butterscotch, Navajo, Ebony, Black Japan & Merbau
Thinner : AQUAPRO 1320 Slow or 133 Medium Reducer
Coverage : 15-25m2 per litre – coverage is determined by application method, strength of colour, timber type, preparation of the surface and the amount of reducer added
Dry Time : Refer to datasheet
Clean Up : Water or AQUAPRO 1320 or 1330 reducer
Packaging : 1 & 5L
Surface Prepartion:
Preparation: Prepare a test area to check colour and application. Prepare the surface by filling nail holes and imperfections with a water based putty in a colour close to the stain. Allow to dry. Sand floor per AS 4786.2-2005 standard to produce a defect and scratch free surface. Finish sanding with 120-180 screen back paper fitted to a rotary sanding machine. Ensure floor is defect and scratch free before applying the stain. Scratches and imperfections may be highlighted by the stain.
Mixing: Stir thoroughly before use.
Tools: Brush, rag or applicator – wipe on and leave or wipe on wipe off.
Application:
- Reduce and mix enough stain for the entire project before starting. Work from one corner as you would when coating a room. Apply to strip flooring along the direction of the grain. Only cut in a small distance in front of your applicator. Do NOT pour or pool stain on the floor. Excess stain must be wiped off.
- Parquetry – apply the stain in an even application across the narrowest part of the floor from side to side until the whole area is stained.
- Even application of the stain is essential to ensure a uniform even colour.
- Allow the stain to dry before applying coatings (see recoat time).
- Ensure adequate coating is applied to seal AQUAPRO 2770 Stain to reduce the risk of sanding through the sealer coat. If this happens, it is possible to reapply the stain to these areas to re-colour the exposed timber.
DURASTAIN 2025 Dye Stain
DURASTAIN 2025 Dye Stain
Interior use only. Timber floors, architraves, skirting boards, timber quadrant and beading
- Versatile – Can be applied over all species of timber
- Medium to slow dry, easy to apply – results in a uniform colour
- Apply by brush, wiping, roller or applicator – no need to wipe off
- Suitable for toning – can be added onto DURAPOL, POLYTHANE or TITAN Gloss coatings to provide a deeper tone colour
Colour : Primary: #5000 Yellow, #7000 Red, #8000 Blue, #9999 Black. Premixed: #6001 Maple, #6004 Oak, #6007 Teak, #6008 Walnut
Thinner : AQUAPRO 1320 Slow or 133 Medium Reducer
Coverage : 10-12m2 per litre – coverage is dependent upon the porosity of the timber
Dry Time : Refer to datasheet
Clean Up : Water or Polycure Super Cleaning Solvent
Packaging : 1 & 5L
Surface Prepartion:
Preparation: Prepare a test area to check colour and application. Prepare the surface by filling nail holes and imperfections with a water based putty in a colour close to the stain. Allow to dry. Sand floor per AS 4786.2-2005 standard to produce a defect and scratch free surface. Finish sanding with 120-180 screen back paper fitted to a rotary sanding machine. Ensure floor is defect and scratch free before applying the stain. Scratches and imperfections may be highlighted by the stain.
Mixing: Stir thoroughly before use.
Tools: Brush, rag, roller or applicator – wipe on and leave or wipe on wipe off.
Application:
- Reduce and mix enough stain for the entire project before starting. Work from one corner as you would when coating a room. Apply to strip flooring along the direction of the grain. Only cut in a small distance in front of your roller or pad applicator. DO NOT pour or pool stain on the floor.
- Parquetry – apply the stain in an even application across the narrowest part of the floor from side to side until the whole area is stained. • Even application of the stain is essential to ensure a uniform even colour.
- Allow the stain to dry before applying coatings (see recoat time).
- Ensure adequate coating is applied to seal DURASTAIN 2025 Stain to reduce the risk of sanding through the sealer coat. If this happens, it is possible to reapply the stain to these areas to re-colour the exposed timber.